2200 LT Round Tank with Double Storey Pump

$999.00

Clear
  • $ 0.00

Description

Enviro Tanks ER2200LT Round Water Tank
Round Water Tanks have domed tops for extra durability, which means that internal supports are not required. All Round Water Tanks have 2x 25mm brass outlets moulded into the tank at the 3 o’clock and 9 o’clock positions. The inlet (leaf strainer) is at the 12 o’clock position. Overflow can be at 12 o’clock, 3 o’clock, 6 o’clock or 9 o’clock. Please call for alternative brass outlets to suit your requirements. Round Water Tanks Sydney

Specifications:

  • 1850mm (Inlet Height)
  • 1300mm (Diameter)
  • 1900mm (Height)

As with all of our tanks, included with the tank is a leaf strainer, ball valve and overflow connection. Overflows are sealed but can be drilled out at the locations specified below.
2x 25mm brass outlets are moulded into the tank at 3 o’clock and 9 o’clock. These outlets are sealed and either or both can be drilled out to suit your requirements. See picture below.
Please see tank colours available on our Colour Matching Guide

 

 

Bianco MK6-FERRO60MPCX Self Priming Cast Iron Jet Pressure Pump 

The pump is a self-priming surface mounted cast iron jet pump supplied with plug and play leads (IEC type). Pump is designed for domestic household water supply, water transfer, tank fillling, garden and irrigation applications

The self-priming ability provides excellent suction capacity of up to 9m.

Features and benefits:

  • Corrosion resistant pump body, diffuser and impeller to ensure pump durability
  • Cataphoresis1 treatment of pump body for rust prevention to ensure no water discoloration or suspended particles
  • High quality mechanical shaft seal and high quality bearings
  • 240V single phase TEFC motor with in-built auto reset thermal overload to prevent the pump from overheating.
  • AS/NZS 4020 Drinking Water Approved for consumer peace of mind

Motor / power: 600W
Volt:  240V
Horsepower: 0.8hp
Head: 45m
Max Flow Rate: 58lt/min
Taps: 4 taps
Warranty on pump: 2 Year
Body: Cast Iron & Technopolymer

 

(Cataphoresis is an electrochemical coating process for metallic surfaces widely used in the industry due to its penetration and long life, either as a priming coat or finished paint for corrosion resistance.)

 

 

Bianco Rainsaver MK6 Mains Switchover

The Rainsaver MK6 replaces all changeover devices switches your system between tank water and town/mains water supply. The system is switched hydraulically, thus requiring no power, and is the least likely system to fail. It also requires the least amount of installation time, saving you time and money. The Bianco Rainsaver MK6 delimits your mains water supply to 200kPa. As long as the pump can supply water greater than 200kPa, which our selected pumps do, it will output tank water. When the water in the tank is insufficient to supply the system, mains water supply is delivered to the home at 200kPa.

There is a pressure drop during the time the system is using mains water supply. The max mains pressure you will get is 200kPa to those taps to which the system is connected. This is normally just the toilets and a couple of outdoor taps. Once the water level in the tanks increases, the system will automatically return to tank supply at full power once again.

As a guide, in Melbourne and Sydney, mains water at the home is between 380 and 600kPa.

ALTERNATIVLY;

Hyjet HHR-550 Mains Switch 

The HYJET HHR-550 is an automatic Rain / Mains change over pump system allowing tank water to be used for water supply in preference to mains water. The HYJET HHR-550 has a quality proven electronic pressure controller which automatically starts the pump when there is demand for water supply. The pressure controller will only operate the pump if tank water is available. The HYJET HHR-550 will automatically switch to mains water when tank water is empty and in case of power failure. The HYJET HHR-550 does not require an in-tank float switch which makes the system quick and easy to install.

Motor / power: 550W
Max. flow:  60 litres / minute
Head: 38m
Pump Inlet diameter: 1″
Mains Inlet diameter: 3/4″
Outlet diameter: 
3/4″
Pump Style: Above Ground
Body Material: AISI 304 stainless steel motor and pump shaft
Warranty on pump: 2 Years

Features

  • No in-tank float switch
  • Quick & Easy to install
  • Suitable for single & double storey homes
  • Automatically switches to mains in case of power failure
  • Watermarked dual check valve for back flow prevention

Application

  • Household water supply & irrigation
  • Submersible installation
  • Water transfer
  • Pressure boosting
  • Industrial wash down

Operating Limits

  • Max. flow rate 60 L/m
  • Max. mains pressure – limited 200 kPa
  • Max. head 38m
  • Max. liquid temperature: 60°C
  • Max. ambient temperature: 40°C
  • Voltage 240V, 50Hz

Materials

  • Pump casing: Stainless steel AISI 304
  • Motor shaft: Stainless steel AISI 304
  • Impellers: polymer
  • Mechanical seal: graphite / ceramic / NBR

Additional information

Capacity

2200LT

Tank Colour

, , , , , , , , , , , , , , , , , , , , , , , ,

Warranty

10 Years Manufacturers Warranty on Tanks, 2 Year Warranty on Pumps